In-Wall thin bezel Subwoofer, perfect for retro-fit! The perfect solution for getting rich, powerful in-wall bass that hides from view.
The new IW-28 SUB is an in-wall subwoofer that uses dual heavy-duty 8" woofers to deliver rich, vibrant bass to custom-installed audio systems.
Boasting amazing hookup flexibility, the IW-28 SUB can either be used passively, driven directly off the receiver's front Left/Right speaker outputs by utilizing the IW-28 SUB's on-board low-pass crossover, OR it can be driven actively by using a power amplifier such as our SA-200 connected to the receiver's 'sub out' jack.
The IW-28 SUB's on-board low-pass crossover is then switched to 'off,' and the crossover functions and bass level duties are handled by the system electronics, as with any powered subwoofer. Several design features distinguish IW-28 SUB's amazing performance--its powerful, long-throw woofers, its solid 1"-thick (!) resonant-free MDF baffle, and its audiophile-grade crossover. This, is one serious subwoofer.
The IW-28 SUB is an in-wall subwoofer that uses dual 8” woofers to deliver rich, vibrant bass to custom-installed audio systems. As can be expected, the IW-28 SUB can be used as the speaker portion of a separately-powered LFE subwoofer in a true 5.1/7.1 system. When used this way, the convenient front-panel switch for the SUB’s crossover would be set to ‘off,’ and the jumpers connecting the two sets of input terminals are left in place. An RCA cable goes from the receiver’s Sub Out jack into a monoblock amplifier (such as Atlantic’s SA-200), and then from the monoblock amp into the 28 SUB. All low-pass/high-pass crossover functions are then handled by the receiver’s bass management system, as when using any powered subwoofer.
However, the IW-28 SUB has two sets of input terminals (one set for each 8” driver) and an on-board passive low-pass crossover so that it can be driven directly off the front left/right speaker outputs of the system’s receiver—without the need for a separate amplifier. When used this way, the jumpers would be removed and the receiver’s L/R outputs simply connect to the individual terminals of each of the IW-28 SUB’s woofers. The IW-28 SUB’s on-board low-pass crossover—switched ‘on’—ensures that the sub receives only the lower bass frequencies
The SA-200 is anewer higher powered monoblock amplifier, and is the perfect companion to the IW-28 SUB. With 200 watts of rock-solid RMS power, a massive toroidal transformer, 12-volt trigger turn-on, and 3-position equalization switch, the SA-200 has all the right moves to make the IW-28 SUB perform at its best.
The stylish new thin bezel design and magnetically attached grille provides a sophisticated and refined look to blend into the wall. Whether it's new construction or retro-fitted into a finished room, the IW-28SUB is one of the most flexible, easy to install, in-wall subwoofers on the market today.
This is one serious home cinema combo, and they don't dissapoint...Proper job!
IW-28 SUB is sold with the SA-200 amp.
Atlantic Technology IW-28 Sub In-Wall Subwoofer Specifications
- Type: Thin Bezel In-Wall Subwoofer
- Drivers: 2 x Woofer - Dual 8" (203mm) long-throw, 40mm voice coil
- Tweeter: N/A
- Frequency Response: 38-200 Hz +/-3dB
- Nominal Impedance: Each driver 8 ohms; paralleled together, system is 4 ohms
- Crossover Frequency: 200 Hz w/built-in low-pass filter
- Sensitivity: 89dB
- Recommended Amplifier Power: 30-200 watts RMS
- Magnetic Shielding: No
- Dimensions w/ grilles (W x H x D): 319 x 554 x 100mm
- Cutout Dimensions (W x H): 283 x 518mm
Atlantic Technology SA-200 Monoblock In-Wall Subwoofer Amplifier Specifications
- Type: Mono Sub Amplifier
- RMS Power: 200 watts, 4 ohms
- Signal to Noise Ratio: Total Harmonic Distortion: 0.05% @ full output
- Low Level Input Sensitivity: 250mw full output, 100Hz
- High Level Input Impedance: 15K Ohms
- Power Supply Storage: 9,400 mfd
- Toroid Transformer(s): 400 VA
- Peak Output Stage Current: 30 amps
- Net Weight: 14 lbs (6.35 kg)
- Height: 2“ 1.5-U (50mm)
- Width: 8.5” (215mm)
- Depth: 12.5" (320mm) including knobs and rear terminals